investigations on replacement of sand by graded quarry dust in concrete

  • Partial Replacement of Sand by Quarry Dust in Concrete

    International Journal of Scientific and Research Publications, Volume 5, Issue 7, July 2015 1 ISSN 2250-3153 Partial Replacement of Sand by Quarry Dust in Concrete Sumit L. Chauhan, Raju A.Bondre Assistant Professor P. I. G. C. E. Nagpur Abstract- The paper describe the role of quarry dust In the of various complex silicates are formed, causing the mass to construction of buildings and other ...

  • IOP Conference Series: Materials Science and Engineering ...

    grades of concrete by replacement of sand with quarry dust. Key Words: Concrete, Compressive strength, Quarry Dust, Replacement, Sand. 1. INTRODUCTION Quarry dust, is a by-product releases from the cutting and crushing process of stone which is a concentrated material to use as fine aggregates. By exploding mountain, rock will be crushed to

  • Evaluation Of Mechanical And Durability Properties Of ...

    replacing fine aggregate with quarry dust. This present work is an attempt to use Quarry Dust as partial replacement for Sand in concrete. Attempts have been made to study the properties of concrete and to investigate some properties of Quarry Dust the suitability

  • An Experimental Investigation on Strengths Characteristics ...

    An Experimental Investigation on Strengths Characteristics of Concrete with the Partial Replacement of Cement by Marble Powder Dust and Sand by Stone Dust Md Mahboob Ali*, Prof. S.M.Hashmi ** *P.G Student of structural Engineering, Department of Civil Engineering, K.B.N College of Engineering, Gulbarga-585104

  • A Study on Performance of Crusher Dust in Place of Sand as ...

    mineralogy of quarry dust varies with aggregate type and source. IllangovanRet.al(2006)3 studied quarry dust as fine aggregate in concrete. Collins R.J et.al (1994)2 studied quarry dust in highway constructions. In the present

  • Research Article Study on Compressive Strength of Quarry ...

    (c) e compressive strength results of quarry dust concrete (cubes) were obtained in the third series, where M, M, and M grades of concrete with,, and percent replacement of quarry dust and also workability are studied by varying the water-cement ratio of . and . and the results are presented. When % sand is replaced with quarry dust, there is a

  • Improved Concrete Properties Using Quarry Dust as ...

     · The results show that there is an increase in the compressive strength of the concrete [3,4] which the increment is about 55% to 75% depending on the replacement if the sand with the quarry dust ...

  • USE OF RICE HUSK ASH AS PARTIAL REPLACEMENT FOR …

    The 0% replacement was to serve as control for other samples. 2.3. Concrete Mix Design The concrete used in this research work was made using Binder, Sand and Gravel. The concrete mix proportion was 1:2:4 by weight. 2.4. Casting of samples Cubic specimens of concrete with size 150 x 150 x 150 mm were cast for determination of all measurements.

  • Implication of Metakaolin in Quarry Dust Concrete

    Ahmed 1989). A complete replacement of quarry dust to river sand as fine aggregate in concrete is possible with proper treatment of quarry dust before utilization (Illangovan et al 2008).The utilization of well graded, fines free quarry dust has been accepted as building material in the industrially advanced countries (Manasseh

  • CIVIL

    Experimental Investigation on Replacement of Sand by Graded Quarry Dust in Concrete CEX002. Experimental Investigation on Partial Replacement of Cement with Glass Powder CEX003. Parametric Study for Replacement of Sand by Fly Ash for Better Packing and Internal Curing ... Experimental Investigation on Concrete with Using E-waste and Marble Dust

  • Utilization of Stone Dust as Fine Aggregate Replacement in ...

    strength in this study the concrete with above 50% replacement level of stone dust casted on 1 - 1.5% dose of super plasticizer with slump vale of 25 – which can be maintained by extra dose of 35 mm. Finally it can be stated that the stone dust is to be used in concrete with partially or fully replacement of fine aggregate. TABLE 4.

  • I am using quarry dust (fine like cement) as a partial ...

    It is good to be creative and to think outside the square. However there are sometimes that things have been done a certain way for a long time for a good reason. The problem is that using what I would call "crusher dust" or "crusher fines" will ...

  • Investigation of the mechanical strength of stone dust and ...

     · Concrete of grade M20 was manufactured in the laboratory with stone dust and ceramic in place of natural sand and stone. The prepared concrete was then investigated for compressive strength and the flexural strength. The ceramic waste replacement was kept constant as 20%, whereas stone dust was used in the range of 0– with the interval of ...

  • EXPERIMENTAL INVESTIGATIONS ON DURABILITY …

    To meet the requirements of globalization, in the construction of buildings and other structures concrete plays the major rightful role and a large quantum of …

  • Replacement Of Sand With Quarry Dust Project

    Partial Replacement of Sand with Quarry Dust in Concrete . Partial Replacement of Sand with Quarry Dust in. Concrete. Chandana Sukesh, Katakam Bala Krishna, P.Sri ... Strength of Concrete by Partial Replacement of Fine Aggregate Using Quarry Dust and Cement by Silica Fume Abstract Sand collected from Aeolian deposit is expensive ...

  • An Investigation into the Use of Manufactured Sand as a ...

    The UK has significant reserves of crusher dust in its quarries, which could undergo further processing to provide the majority of the sand required by ... results in a well graded and shaped sand product with a filler component mostly comprising fines. ... subsequently used as a replacement for natural sand in concrete. The structure ...

  • [PDF] Experimental Investigation on the Effect of ...

    The demand of natural sand in the construction industry has increased a lot resulting in the reduction of sources and an increase in price. Thus an increased need to identify a suitable substitute, that is eco-friendly and inexpensive quarry dust being extensively used as an alternative to the sand in the production of concrete. In this paper an attempt has been made to determine the ...

  • (PDF) EXPERIMENTAL STUDY ON PARTIAL REPLACEMENT OF SAND …

    The overall test results disclosed the wooden powder dust with the different percentage in that quarry waste fine aggregate can be utilized in concrete the concrete and to check the properties of the concrete by mixtures as a good substitute of natural sand. comparing with the normal concrete. The replacement of fine aggregate (sand) with ...

  • Use of Quarry Dust to Replace Sand in Concrete – An ...

    III. EXPERIMENTAL INVESTIGATION A. Mix proportioning Two grades of concrete M20 and M25 having nominal mix proportion of 1:1.5:3 and 1:1:2 respectively were used by weight and w/c ratio was fixed according to the slump requirement of 60mm. For this concrete mix, quarry dust was added for replacement of sand from 0% to in step of 10%.

  • granite fine sand replacement

    Experimental Analysis on Partial Replacement of Fine,Know More Dec 31, 2018· Sand was replaced by mass fractions of 0, 5, 10, 15, 20, 30 and 40% with granite dust The study reflected that replacement of sand by granite dust up to 20% showed better strength than conventional concrete The comparison study of bond strength with and without replacement of granite dust using different diameters ...

  • Improved Concrete Properties Using Quarry Dust as ...

     · Improved Concrete Properties Using Quarry Dust as Replacement for Natural Sand 52 VII. APPLICATIONS 1) The quarry dust is widely used in construction industry. 2) Quarry dust is used as a fine aggregate in Concrete for paving blocks of good permeability capacity and high grade concrete productions. 3) Quarry dust gives better workability and ...

  • A STUDY ON PARTIAL REPLACEMENT OF CEMENT WITH …

    replacement of natural sand by quarry sand and 1.5 % dosage of mixture. Split tensile strength of concrete, when cement is replaced with 40% of GGBS & 60% of quarry dust for maximum dosage of mixture.Flexural strength will be max, if 30% of cement by GGBS & 60% of quarry sand as constant replacement for fine aggregates.

  • Experimental Investigation on Quarry Dust as a Partial ...

    concrete mix and quarry dust will be used as a fine aggregate. The gravity quarry dust is replaced by sand varying different percentage (0%, 15%, 30%, 45%, 60% & 75%). then test data of quarry dust concrete will be compared with test data from a standard concrete without quarry dust Keywords: Quarry, water cement ratio, compressive

  • Characteristic studies on the mechanical properties of ...

    Quarry dust The basic tests on quarry dust were conducted as per IS-383-1987 and its specific gravity was around 1.95. Wet sieving of quarry dust through a 90 micron sieve was found to be 78% and the corresponding bulking value of quarry dust was 34.13%. Coarse aggregate replacement of sand with quarry dust of mortar cube (C

  • (PDF) Improved Concrete Properties Using Quarry Dust as ...

    Table 3 The results show that there is an increase in the compressive strength of the concrete [3,4] which the increment is about 55% to 75% depending on the replacement if the sand with the quarry dust, for the replacement of the sand the compressive strength is depending on the quarry dust location from where the quarry dust was taken.

  • Replacement of cement by glass powder and sand quarry dust

     · Obviously increasing in water content in the mixture will adversely affect the quality of concrete The measured slump values of quarry dust concrete with constant water cement ratio 0.55 are found to be 37, 45, 50, 54 and 60 mm for different mixes The measured compaction factor value for quarry dust concrete with constant w/c ratio (0.55) are ...

  • (PDF) EXPERIMENTAL INVESTIGATIONS ON DURABILITY ...

    [3] ChandanaSukesh "Partial Replacement of Sand with Quarry Dust in Concrete" by, International Journal of innovative Technology and Exploration and Engineering (IJITEE), VOL.2, MAY 2013.

  • Investigation on mechanical properties of composite ...

     · The concrete mix M4 (50% USS + 50%QD) is the optimum mix for complete replacement of river sand with both sea sand and quarry dust as fine aggregate. b) The 28-day compressive strength is maximum for the M6 mix ( QD) is 40.8 ± 1.15 MPa and lowest is for M2 mix ( USS) is 29.7 ± 0.90 MPa among all excluding control mix.

  • Partial Replacement of Sand by Quarry Dust in Concrete

    investigated the partial replacement of sand with quarry dust. Initially cement concrete cube was studied with various proportions of cement concrete + quarry dust (M 20, AND M25). The experimental results showed that the addition of quarry dust as fine aggregate ratio of 30%, 40% and 50% was found to enhance the compressive properties.

  • Experimental Investigation in Concrete by Partial ...

    28 days, the value is high and it show that quarry dust suitable to use as sand replacement. All the value of compressive strength surpasses the minimum value of compressive strength for normal concrete and hence quarry dust can apply as sand replacement in concrete mix for …

  • An Experimental Investigation on Properties of Concrete by ...

    The replacement percentages of Cement with GGBS are 20 %, 40 % and 60 % by weight and 25 %, 50 %, 75 % and 100 % of Quarry Dust are used as a replacement of Natural Sand. Various combination of GGBS and Quarry Dust were prepared using M30 Grade of Concrete. The effect on these replacement materials on Compressive Strength, Split Tensile ...

  • What are the advantages of using quarry dust as fine ...

    The concept of replacement of natural fine aggregate by quarry dust which is highlighted in the study could boost the consumption of quarry dust generated from quarries. By replacement of quarry dust, the requirement of land fill area can be reduc...

  • Experimental study on high volume fly ash concrete made ...

     · When compared with conventional concrete, 28 days Split tensile strength of 5% coir pith and 75% quarry dust replacement of sand concrete was reduced 14.81%. Split tensile strength of 50% replacement of fly ash by cement concrete is increased when compared with 75% replacement of fly ash by cement concrete.

  • Partial Replacement of Cement With Marble Powder in Concrete

    Due to marble dust, it proved to be very effective in assuring very good cohesiveness of mortar and concrete. From the above study, it is concluded that the marble dust can be used as a replacement material for cement ; and 30 to 40% replacement of marble dust gives an excellent result in strength aspect and quality aspect.

  • Partial Replacement Of Sand By Graded Quarry Dust In ...

    dust as the fine aggregate decreases the cost of concrete production in terms of the ... quarry dust to be used as partial replacement material for sand in concrete. 2. ... In the present study an ordinary Portland cement (OPC 53 grade) was used.

  • (PDF) Use of Quarry Dust to Replace Sand in Concrete – An ...

    A. Mix proportioningTwo grades of concrete M20 and M25 having nominal mix proportion of 1:1.5:3 and 1:1:2 respectively were used by weight and w/c ratio was fixed according to the slump requirement of 60mm. For this concrete mix, quarry dust was added for replacement of sand …

  • ANALYSIS ON STRENGTH OF CONCRETE BY PARTIAL …

    used in the concrete. ii. Robosand Robosand or M-Sand was used as replacement of fine aggregate. Robosand is a result of crushed stone, here the stones are pulverized into smaller granular size of river sand granules and washed to expel the fine rock dust to enhance the quality as per IS: 2386-1975The properties of robosand are shown in Table-3.

  • Investigation of coal bottom ash and fly ash in concrete ...

     · Slump is a measure indicating the consistency or workability of concrete. The effect of CFA as cement replacement and CBA as replacement of sand in concrete mixtures on slump values with similar w/c, are tabulated in Table 3. Slump values of control mix C0, FBC1, FBC2, FBC3 and FBC4 were 73 mm, 92 mm, 76 mm, 53 mm and 37 mm, respectively. Since ...

  • The Utilization Of Crushed Stone Dust As A Replacement Of ...

    Mr.A.C.Dubal Journal of Engineering Research and Application ISSN : 2248-9622, Vol. 8, Issue 9 (Part -III) Sep 2018, pp 11-14 RESEARCH ARTICLE OPEN ACCESS The Utilization Of Crushed Stone Dust As A Replacement Of Sand In Cement Concrete Mr.A.C.Dubal Assistant ProfessorSYMBIOSIS SKILL & OPEN UNIVERSITY PUNE.PhD Scholar M.E.Civil (Structure),M.B.A,LMISTE ABSTRACT In concrete …

  • Partial Replacement of Sand with Quarry Dust in Concrete ...

    -The reduction in the sources of natural sand and the requirement for reduction in the cost of concrete production has resulted in the increased need to identify substitute material to sand as fine aggregates in the production of concretes especially in Concrete. Quarry dust, a by-product from the crushing process during quarrying activities is one of such materials.

  • Effective Utilization of Crusher Dust in Concrete Using ...

    the natural sand in concrete control mixes of M25 and M30 grades designed for 100 to 120mm slump at replacement levels of 30%, 40%, 50% and 60% using Portland Pozzolana Cement. There were in all 5 mixes in each grade of concrete including control mix and four mixes with crusher dust as a partial replacement of natural sand.

  • PARTIAL REPLACEMENT OF CEMENT BY QUARRY DUST

    observed that by 25% of partial replacement of cement with quarry dust improved hardened concrete properties. Keywords: Quarry dust, cement, water, aggregates. -----***-----1. INTRODUCTION Quarry dust is a waste product obtained from quarrying. It can be …

  • Replacement of Sand with Bauxite Mining Waste in Concrete ...

    The use of natural sand as fine aggregate in concrete is becoming problematic due to scarcity and pressure on mining of the resource. Alternate sources such as the use of industrial waste as replacement of natural sand in concrete are gaining popularity as a sustainable construction material.

  • Stone Dust in Concrete: Effect on Compressive Strength

    found that the compressive and flexural strength of concrete made of Quarry Rock Dust are nearly 10% more than the conventional concrete (Suribabu et al., 2015). In the present study it is proposed to investigate the optimum replacement of river sand with stone dust for concrete in term of compressive strength performance at 7 days and 28 days. II.

  • Quarry fines: an ideal material for the manufacture of ...

     · Fayaz et al. reported that there was 5–22% enhancement of strength for concrete at high substitution levels of river sand by quarry dust up to . It has been found that there was enhancement in flexural strength by about 4.3% due to the inclusion of very fine quarry dust in concrete (Meisuh et al. 2018).